"Here is everything that has to do with the formula for ancient annealed bronze."

It is opposite to annealed disorder, where the random variables are allowed to evolve themselves.

The annealed crystals are then cut into gemstones.

Toughened glass is typically four to six times the strength of annealed glass.

Common annealed glass breaks fairly easily into jagged shards.

A fierce and recalcitrant part of him felt as she did, fought like loathing against his annealed purpose.

By using annealed glass in small panes.

He was harder than any granite, more rigid than any annealed metal.

They would slide down them and crawl among the old freezer plant, mining out a few cans from the annealed sand.

In some contexts, the opposite of quenched disorder is annealed disorder.

The bends are made of special annealed pipes at normal temperature, using a custom-made bender.

The idea of using annealed Ising models for inference is often thought to have been first described by:

Typical tempers are soft annealed and rolled hard.

The metal is nearly as soft as annealed copper, yet once it was hard and strong as steel.

Cast-steel is often normalized rather than annealed, to decrease the amount of distortion that can occur.

Toughened glass is made from annealed glass via a thermal tempering process.

In the annealed condition, tantalum is extremely ductile and can be readily formed as metal sheets.

Annealed glass undergoes a similar deflection compared to tempered glass under the same load.

In contrast, the same steel composition in annealed state will be softer as required for forming and machining.

For annealed materials the Meyer hardness increases continuously with load due to strain hardening.

In the annealed state it has a hardness of 27 HRC.

Annealed glass breaks into large, jagged shards that can cause serious injury, and thus, the reason it is considered a hazard in architectural applications.

Her method involves sandblasting the annealed glass, creating a pitted surface that can be embellished with drawing and painting.

Annealed glass, heat-strengthened or tempered glass can be used to produce laminated glass.

In mathematical terms, quenched disorder is harder to analyze than its annealed counterpart, since the thermal and the noise averaging play very different roles.

The pistol had become a part of his hands, annealed to them.

The thought of going back to a strip once annealed had never occurred to him.

The metal there would be annealed by the heat of his torch.

"See how this penny is annealed to the back of the fuse?"

Then when you heated it the penny the metal was annealed.

Since the base of the case must be hard, it cannot be annealed.

The plates are annealed for approximately 10 hours and then allowed to slowly cool.

During this process the piece becomes very hard and has to be annealed several times, then worked again until the final shape is achieved.

Nightmares of fire had annealed him to his purpose.

They are then annealed again to remove any strain hardening.

The music is annealed by his time here.

The fever which threatened to paralyze her could only be annealed in fire.

If the metal is annealed it will sink in around the indentation.

Float glass is annealed during the process of manufacture.

The glass is then annealed and cut into 7 to 10 foot (2 to 3 m) cylinders.

A different set of eight wafers are annealed together.

Her mouth fused with his; their bodies were sealed and annealed.

These were further drawn and then dried and annealed at about 260 degrees.

The graphite had to be placed in a hot zone, annealed and then pulled back out for testing.

The obtained glass is usually annealed to prevent breakage during processing.

If not, they are irradiated by high-energy particles and annealed.

And the zinc alloy is probably the bulk metal which was annealed.

Brittle wire that has not been annealed may snap during the drawing process.

In order for the copper to be worked to any extensive degree it must be annealed.

The material is then annealed to relieve stress that was caused by the machining.